FAQs
What does E3 mean on an Ashley pellet stove? ›
E4 is a 12 Minute time out if there is no fire in 12 minutes. This could be a bad sensor. E3 error means the hopper ran out of pellets. This could also be a bad sensor.
Why won t my pellet stove fire up? ›In conclusion, ignition failures in pellet stoves and pellet stove inserts can often be traced back to issues with the exhaust fan, auger, igniter, airflow, and burn pot cleanliness.
What does E4 mean on a pellet stove? ›E4 error code. Igniter will not light fuel. • Check electrical connections (including fuse) to the igniter • Check that the igniter tube, which touches the burn pot, is not plugged with ash.
How do I get rid of E3 error on my induction stove? ›- Wait for the unit to cool.
- Turn the home circuit breaker to the unit off for 30 seconds then back on again.
- Retest the unit operation.
- If these steps do not resolve the issue, no further troubleshooting advice is available. Contact Factory Certified Service to schedule an appointment for repair.
The E3 error code means that your unit has overheated.
Is there a reset button on a pellet stove? ›Many pellet stoves do not have a pellet stove reset button. Instead, you can reset them by letting the pellets run out. This way, you don't have to try to move pellets out of the stove when you are not sure if it is hot. Once the stove runs out of pellets, it will no longer be able to heat.
What is error 3 on King pellet stove? ›I get an error message 3. The manual says this error indicates “The stove was unable to reach the Room Fan On temperature within the startup time.” The cause is “Flame or Fuel quality caused the fire to burn too slowly or go out. Auger output failure or jam Hopper empty on startup.”
What setting should my pellet stove be on? ›Thinking of Using a Thermostat with Your Pellet Stove? If you are using a wall thermostat, it is best to set your appliance on a medium heat setting. When the thermostat calls for heat the unit will change from a pilot fire to the medium setting and bring your home up to the desired temperature.
Why is my pellet stove not igniting pellets? ›Check the Pellets: Inspect your pellets for any signs of moisture or poor quality. If they're damp or clumped together, replace them with fresh, dry pellets. Inspect the Airflow: Check the air inlet pipe, the outside air kit, and any areas inside the stove downwind from the burn pot for blockages.
Why are my pellets not catching fire? ›Troubleshoot like a pro.
Adjust heat setting to medium or medium/high. Clean all vents, check and repair/replace all gaskets, adjust damper or airflow setting. Adjust air-to-pellet ratio by increasing air flow. Adjust air-to-pellet ratio by increasing air flow and/or decreasing feed rate.
What is error 3 on ashley pellet stove? ›
During start-up ignition must occur within 12 minutes or the stove will error out and show E3. During the start-up phase, the Mode key does not function. These buttons when pushed will set the pellet feed rate, hence the heat output or heat range of your stove.
How to fix E3 fireplace code? ›Unplug the unit and clean any dust or debris from the vent area. Leave the fireplace insert unplugged for 5 minutes, plug the power back in and turn on the heater.
What is the error code E3? ›When you see the error code 'E3', it is indicating that there is either a fault with the indoor fan motor or there's a problem with the indoor PCB.
What is E3 on my air condition? ›The E3 error code indicates the unit has detected there is no refrigerant. The unit will require a repair service for refrigerant to be added, please visit Request a Repair page for further assistance.
How do I fix my E3 error on my air fryer? ›Getting down to the error code, the E3 is meaning for the overheating error code. When your unit does not have enough water in it or there is early steam release, the unit will go into an Error code and it will display the E3. To get rid of the E3, you want to unplug the unit and let it cool down.